(1)Body Smoothing Hammer with a 0.401 shank fits most standard Air Hammers. Black oxide finish hardened steel with a 1.5" Diameter convex face. Works great alone for roughing out a panel or smoothing with a back-up dolly. Made in USA.
Air Hammer is not included.
(1)Designed to be used with the Stud Welder System, this tool makes it easy to repair minor dings and dents, due to hail, parking lots, etc. Just weld a draw-pin (stud) to the surface, attach the tool to the pin, slowly squeeze the handles until the dent is flush with the surface, then snip-off the draw pin.
(11)Wilmar W1028 Suction Cup Dent Puller
For best results, use on clean, flat surfaces with smooth finish. Objects with textured, brushed or satin finishes or surface variations degrade the air-tightness of vacuum seal reducing lift capacity. Pulling/lifting at angle other-than 90-degrees from surface also affects performance. In our tests, the cups were placed on flat 18-ga sheet metal with semi-gloss finish and lift was applied at 90-degrees until cups broke free - consistently requiring more than 75 lbs of lift. Coating cup-rim lightly with small amount of vegetable/petroleum oil may improve seal quality on some surfaces.
T&E; 1882 Pneumatic Dent Puller W 3 Cups 1882 T&E Tools Pneumatic Dent Puller. The pneumatic dent puller has 3lb.(1.36kg) slide hammer and is fitted with a brass shut off valve. It is supplied with three different size screw on suction pads. Simply select the correct size pad to remove the dent, apply shop air and use the slide hammer. Compressed air is exhausted through the handle and unit is fitted with 13"(330mm) inlet hose with 1/4"NPT air plug. Slide Hammer Length: 24"(600mm) Pad Sizes: 1: 60mm Screw On Suction Pad 2: 120mm Screw On Suction Pad 3: 150mm Screw On Suction Pad
(5)Bondo Locking Suction Cup Dent Puller has 300 times more suction than other non-locking suction cup dent pullers. It can pull out large dents without leaving holes behind that need to be filled.
(12)
For best results, use on clean, flat surfaces with smooth finish. Objects with textured, brushed or satin finishes or surface variations degrade the air-tightness of vacuum seal reducing lift capacity. Pulling/lifting at angle other-than 90-degrees from surface also affects performance. In our tests, the cups were placed on flat 18-ga sheet metal with semi-gloss finish and lift was applied at 90-degrees until cups broke free - consistently requiring more than 50 lbs of lift. Coating cup-rim lightly with small amount of vegetable/petroleum oil may improve seal quality on some surfaces.
(53)This easy to use, inexpensive Glue Puller Kit allows for simple, cost efficient removal of small to medium dents/dings on all panels of your vehicle. More and more, light gauge sheet metal is being used in the construction of vehicles. You can actually dent many new cars by simply leaning against them. Dent Out Glue puller kits allow the do-it-your-selfers, a professional option to expensive dent removal services. No need to access the underside of the panel. Each unique kit offers a tool for specific damage. With three kits available, they encompass all types of dent repair. Simply apply a bead of glue to the pulling nib and affix the nib to the lowest area of the dent. The tool slips over the threaded stud. A wing nut tool is threaded down pulling the metal up. Once the dent is pulled out, a couple of drops of release agent is applied to the glue and the pulling nib comes right off. Use only on OEM baked finishes. This product will not damage your factory finish.
(104)DO-IT YOURSELF! DENT AND DING REPAIR KIT Featuring unique patent-pending bridge and adhesive system designs. Its the one professionals use! It|s simple to use, just three easy steps and Pops-A-Dent removes dents from hail, other car doors, and more ... without damaging the surface of your car! Pops-A-Dent saves you money and is the economical alternative to costly dent professionals.
For a video demo go to www.denthammer.com If you've been shopping for a glue puller, you've come to the right place. Slide hammer glue pullers are the best on the market. They provide much more control in your pulls than twist or handle pullers. It's very difficult to do small consecutive pulls with other types of pullers. Slide hammers give you the ability to do quick little pulls while watching your progress. You can take your time with the pulling process rather doing abrubt quick pulls that the other types of glue pullers offer. These glue pullers work great for pulling out small, medium and large size dents.Warning-any glue puller that rests on the vehicle panel can put new dents in the vehicle. Slide hammers won't put you at risk of adding new dents. This slide hammer comes with 6 glue pulling tabs ranging from 1/2" to 1-1/4" diameter. Also included is a glue gun, nylon knock down for tapping down high spots and 6 extra strength black glue sticks and glue release solution. User instructions included. (Fits most standard pulling tabs if you would like to ad to your tab styles) Glue pullers are a great asset to the dent repair newcomer and the experienced tech. Glue pullers can help you when the car panel can't be accessed using metal rods or to give you a head start on larger dents. Please NOte: glue puller kits will not work on every type of dent. Very rigid areas of the car panel, body lines and deep dents are not suitable for glue pullers. Works best on pliable metal like hoods and center of door panels
(1)seen on tv
(6)Strong reinforced Nylon lever with pivoting base and self-locking stud capture mechanism allows the technician to quickly lock and lever studs while also compressing the crown area of the dent with the pivoting base. Adjustable pivot base on the Stud Lever allows one-handed operation and provides increased leverage, accuracy and reach for the pull and crown compression processes both vertical and horizontal, including roofs and lower rocker panels. Stud Lever’s unique stud capture mechanism allows technician to quickly and easily capture both 2.2mm and 2.6mm studs as close as 3/8 inches apart. Included with the Stud Lever is the Steck Straight Edge, part number 20003, which allows the technician to align the stud pull with the non-damaged metal area for accurate pulls on the initial pull which minimizes metal work and reduces the need for slide hammers.
This variety pack of glue pulling tabs enables you the right tab for the task at hand.
(3)Paintless dent repair (PDR) glue for use with glue gun in the Keco Super Tab Dent Pulling kit - ASN B003O9ISA8 SPECIAL OFFER: With each order receive a FREE variety pack of (3) KECO glue tabs-Retail value $5.55 (as of 01/07/2013 09:52 PST)- (one per customer per invoice)
(30)Brand New Mini Suction Dent Puller - 6cm Diameter Quantity: 2 Diameter: 6cm (@ 2") Perfect For Pulling Out Metal Dents! Can Also be Used to Lift Glass, Sheet Metal, or any other Smooth Surface Quick Release Handle
(28)The Astro Pneumatic 9038 Single Suction Cup features a 4-5/8-Inch diameter rubber suction cup with lever lock capability for secure grip. This cup is designed for one person auto glass repair and can also be used for small dent removal. The suction cap has a capacity of 88-Pound.
(46)
Amazing amount of holding/pulling power in an easy-to-handle size for applications too tight for regular-size cups. Rugged impact-resistant nylon construction. For best results, use on smooth non-porous surface; both surface and rubber cup should be clean and free from dirt. Apply pressure to handle against surface while lifting handle levers; lubricating cup rim with small amount of oil or liquid typically enhances rubber-to-surface seal and helps improve vacuum strength. Applying excessive lubrication may allow undesired cup movement on surface.
(93)Pulls out small dents by suction power alone! Many other holding and pulling applications. Super-tough rubber cup and one-piece cast aluminum grip.
